Repeater · Room Server · Companion

MeshCore CLI-referentie

Alle commando's van de seriële console, met standaardwaarden en Nederlandse richtlijnen voor het instellen van je node.

92 commando's · bijgewerkt op 13-08-2026 · bron laatst gewijzigd 20-07-2026

De commandobeschrijvingen komen uit de officiële MeshCore CLI-documentatie (MIT-licentie) en zijn daarom Engelstalig: een commandoreferentie vertalen introduceert fouten die je juist hier niet wil hebben. Blokken met NL zijn van ons. Dat is community-advies, geen officiële bron. Een vanaf v1.x-badge verschijnt alleen waar de documentatie de introductieversie expliciet noemt (17 van de 92); ontbreekt hij, dan is de versie niet vermeld, niet dat het commando er altijd was.

Recent gewijzigd in de officiële documentatie(geconstateerd op 09-08-2026)

nieuwtime, Set the time to a specific timestamp
nieuwadvert, Send a flood advert

Operational 10

reboot

Reboot the node

reboot

poweroff

Power-off the node

poweroff

shutdown

clkreboot

Reset the clock and reboot

clkreboot

clock sync

Sync the clock with the remote device

clock sync

clock

Display current time in UTC

clock

time

Set the time to a specific timestamp

time <epoch_seconds>

start ota

Start an Over-The-Air (OTA) firmware update

start ota

erase

Erase/Factory Reset

erase

Laatste redmiddel

Neighbors 3

neighbors

List nearby neighbors

neighbors

Repeater Only

Diagnose

neighbor.remove

Remove a neighbor

neighbor.remove <pubkey_prefix>

Repeater Only

Diagnose

discover.neighbors

Discover zero hop neighbors

discover.neighbors

Repeater Only

Diagnose

Statistics 4

clear stats

Clear Stats

clear stats

stats-core

System Stats - Battery, Uptime, Queue Length and Debug Flags

stats-core

Diagnose

stats-radio

Radio Stats - Noise floor, Last RSSI/SNR, Airtime, Receive errors

stats-radio

stats-packets

Packet stats - Packet counters: Received, Sent

stats-packets

Logging 4

log start

Begin capture of rx log to node storage

log start

log stop

End capture of rx log to node storage

log stop

log erase

Erase captured log

log erase

log

Print the captured log to the serial terminal

log

Info 2

ver

Get the Version

ver

board

Show the hardware name

board

Configuration 69

radio

View or change this node's radio parameters

get radio

set radio <freq>,<bw>,<sf>,<cr>

standaard 869.525,250,11,5Radio

NL preset (SF7/CR5)

tx

View or change this node's transmit power

get tx

set tx <dbm>

standaard Varies by boardRadio

Zendvermogen & ERP

tempradio

Change the radio parameters for a set duration

tempradio <freq>,<bw>,<sf>,<cr>,<timeout_mins>

Radio

Preset veilig uitproberen

freq

View or change this node's frequency

get freq

set freq <frequency>

standaard 869.525Radio

Frequentiegebied NL

radio.rxgain

View or change this node's rx boosted gain mode (SX12xx and LR1110, v1.14.1+)

get radio.rxgain

set radio.rxgain <state>

standaard onvanaf v1.14.1Radio

radio.fem.rxgain

View or change the LoRa FEM receive-path gain state on supported boards

get radio.fem.rxgain

set radio.fem.rxgain <state>

Radio

name

View or change this node's name

get name

set name <name>

standaard Varies by boardSystem

lat

View or change this node's latitude

get lat

set lat <degrees>

standaard 0System

Locatie is publiek

lon

View or change this node's longitude

get lon

set lon <degrees>

standaard 0System

Locatie is publiek

prv.key

View or change this node's identity (Private Key)

get prv.key

set prv.key <private_key>

System

Identiteit & sleutelbeheer

password

Change this node's admin password

password <new_password>

standaard passwordSystem

NLWijzig dit direct na het flashen, de standaardwaarde is bij iedereen bekend.

Standaardwachtwoorden

guest.password

View or change this node's guest password

get guest.password

set guest.password <password>

standaard <blank>System

Standaardwachtwoorden

owner.info

View or change this node's owner info

get owner.info

set owner.info <text>

standaard <blank>vanaf v1.12System

adc.multiplier

Fine-tune the battery reading

get adc.multiplier

set adc.multiplier <value>

standaard 0.0 (value defined by board)System

public.key

View this node's public key

get public.key

System

ver

View this node's firmware version

ver

System

role

View this node's configured role

get role

System

powersaving

View or change this node's power saving flag (Repeater Only)

powersaving

powersaving on

powersaving off

standaard offSystem

repeat

View or change this node's repeat flag

get repeat

set repeat <state>

standaard onRouting

NLWerkt alleen op repeater- en room-server-firmware; de vlag wordt op companions niet uitgelezen. off maakt er een observer van: luistert mee, stuurt niets door.

Observer-modus

path.hash.mode

View or change this node's advert path hash size

get path.hash.mode

set path.hash.mode <value>

standaard 0vanaf v1.14Routing

NLNederlandse richtlijn: 1 (2-byte). Veilig: het raakt alleen je eigen adverts, niet wat je doorstuurt.

Multi-byte path hash

loop.detect

View or change this node's loop detection

get loop.detect

set loop.detect <state>

standaard offvanaf v1.14Routing

NLNederlandse richtlijn: minimal. De firmware-standaard is off, dus dit moet je expliciet zetten.

Loop detection

txdelay

View or change the retransmit delay factor for flood traffic

get txdelay

set txdelay <value>

standaard 0.5Routing

NLLaat op 0.5 staan; geef naburige repeaters bewust verschillende waarden om botsingen te spreiden.

TX Delay

direct.txdelay

View or change the retransmit delay factor for direct traffic

get direct.txdelay

set direct.txdelay <value>

standaard 0.2Routing

TX Delay

rxdelay

[Experimental] View or change the processing delay for received traffic

get rxdelay

set rxdelay <value>

standaard 0.0Routing

TX Delay

dutycycle

View or change the duty cycle limit

get dutycycle

set dutycycle <value>

standaard 50% (equivalent to airtime factor 1.0)vanaf v1.15.0Routing

NLZet dit op 10. De firmware-standaard van 50% ligt ver boven wat sub-band P in Nederland toestaat.

Duty cycle & airtime factor

af

deprecated sinds v1.15.0

View or change the airtime factor (duty cycle limit)

get af

set af <value>

standaard 1.0Routing

NLVerouderd sinds v1.15.0. Op oudere firmware is 9 de waarde die op ~10% duty cycle uitkomt, niet 1.

Airtime factor (verouderd)

int.thresh

View or change the local interference threshold

get int.thresh

set int.thresh <value>

standaard 0.0Routing

cad

Enable or disable hardware Channel Activity Detection (CAD)

get cad

set cad <on|off>

standaard offRouting

NLLaat off staan tenzij je het verschil meet. MeshCore houdt de standaard op uit omdat hardware-CAD de node af en toe zo'n vier seconden stillegt en de vernieuwde listen-before-talk even goed presteert. Tot v1.17.0 zat deze scan vást aan int.thresh; had je die drempel gezet, dan stond CAD ongemerkt aan en na het bijwerken niet meer. Dit is geen gecertificeerde LBT: de duty cycle van 10% blijft in Nederland gelden.

Listen before talk en CAD

agc.reset.interval

View or change the AGC Reset Interval

get agc.reset.interval

set agc.reset.interval <value>

standaard 0.0Routing

NLBij een repeater die niets meer hoort: 4. Lost het meest voorkomende doofheidsprobleem op SX1262 op.

Repeater wordt doof

multi.acks

Enable or disable Multi-Acks support

get multi.acks

set multi.acks <state>

standaard 0Routing

flood.max

Limit the number of hops for a flood message

get flood.max

set flood.max <value>

standaard 64Routing

Flood beperken

flood.max.unscoped

Limit the number of hops for an unscoped flood message

get flood.max.unscoped

set flood.max.unscoped <value>

standaard 64 - (0xFF indicates it hasn't been set, will track flood.max until it is.)Routing

Regio-doorsturing

setperm

Add, update or remove permissions for a companion

setperm <pubkey> <permissions>

ACL

Rechten per gebruiker (ACL)

acl

View the current ACL

get acl

ACL

Rechten per gebruiker (ACL)

allow.read.only

View or change this room server's 'read-only' flag

get allow.read.only

set allow.read.only <state>

standaard offACL

Rechten per gebruiker (ACL)

region load

Bulk-load region lists

region load

region load <name> [flood_flag]

vanaf v1.10Region Management

region save

Save any changes to regions made since reboot

region save

vanaf v1.10Region Management

region allowf

Allow a region

region allowf <name>

vanaf v1.10Region Management

Voorbeeldconfiguratie

region denyf

Block a region

region denyf <name>

vanaf v1.10Region Management

Regio-doorsturing

region get

Show information for a region

region get <name>

vanaf v1.10Region Management

Configuratie controleren

region home

View or change the home region for this node

region home

region home <name>

vanaf v1.10Region Management

default versus home

region default

View or change the default scope region for this node

region default

region default {name|<null>}

vanaf v1.10Region Management

default versus home

region put

Create a new region

region put <name> [parent_name]

vanaf v1.10Region Management

Voorbeeldconfiguratie

region def

Define region hierarchy (single line)

region def <token> [<token> ...]

vanaf v1.10Region Management

Kortere notatie

region remove

Remove a region

region remove <name>

vanaf v1.10Region Management

region list

View all regions

region list <filter>

vanaf v1.12Region Management

Configuratie controleren

region

Dump all defined regions and flood permissions

region

vanaf v1.10Region Management

Regions en scope

gps

View or change GPS state

gps

gps <state>

standaard offGPS (When GPS support is compiled in)

gps sync

Sync this node's clock with GPS time

gps sync

GPS (When GPS support is compiled in)

gps setloc

Set this node's location based on the GPS coordinates

gps setloc

GPS (When GPS support is compiled in)

Locatie is publiek

sensor list

View the list of sensors on this node

sensor list [start]

Sensors (When sensor support is compiled in)

sensor get

View or change the value of a sensor

sensor get <key>

sensor set <key> <value>

Sensors (When sensor support is compiled in)

bridge.type

View the compiled bridge type

get bridge.type

Bridge (When bridge support is compiled in)

bridge.enabled

View or change the bridge enabled flag

get bridge.enabled

set bridge.enabled <state>

standaard offBridge (When bridge support is compiled in)

Wat is de bridge?

bridge.delay

Add a delay to packets routed through this bridge

get bridge.delay

set bridge.delay <ms>

standaard 500Bridge (When bridge support is compiled in)

Wat is de bridge?

bridge.source

View or change the source of packets bridged to the external interface

get bridge.source

set bridge.source <source>

standaard logTxBridge (When bridge support is compiled in)

Wat is de bridge?

bridge.baud

View or change the speed of the bridge (RS-232 only)

get bridge.baud

set bridge.baud <rate>

standaard 115200Bridge (When bridge support is compiled in)

Wat is de bridge?

bridge.channel

View or change the channel used for bridging (ESPNow only)

get bridge.channel

set bridge.channel <channel>

Bridge (When bridge support is compiled in)

Wat is de bridge?

bridge.secret

Set the ESP-Now secret

get bridge.secret

set bridge.secret <secret>

standaard Varies by boardBridge (When bridge support is compiled in)

Wat is de bridge?

bootloader.ver

View the bootloader version (nRF52 only)

get bootloader.ver

Bridge (When bridge support is compiled in)

pwrmgt.support

View power management support

get pwrmgt.support

Bridge (When bridge support is compiled in)

pwrmgt.source

View the current power source

get pwrmgt.source

Bridge (When bridge support is compiled in)

pwrmgt.bootreason

View the boot reset and shutdown reasons

get pwrmgt.bootreason

Bridge (When bridge support is compiled in)

Diagnose

pwrmgt.bootmv

View the boot voltage

get pwrmgt.bootmv

Bridge (When bridge support is compiled in)

Diagnose

eth.status

View Ethernet connection status

eth.status

Ethernet (when Ethernet support is compiled in)

Bronnen

Officiële CLI-referentie: de bron van de commandobeschrijvingen op deze pagina
MeshCore FAQ: achtergrond bij veel van deze instellingen
docs.meshcore.io: officiële documentatiesite
Over MeshCore: onze uitleg van het protocol, de NL-instellingen en de regelgeving
Regio Generator: genereert de region put-reeks voor je eigen repeater

MeshCore CLI-referentie

Operational 10

reboot

poweroff

clkreboot

clock sync

clock

time

advert

advert.zerohop

start ota

erase

Neighbors 3

neighbors

neighbor.remove

discover.neighbors

Statistics 4

clear stats

stats-core

stats-radio

stats-packets

Logging 4

log start

log stop

log erase

log

Info 2

ver

board

Configuration 69

radio

tx

tempradio

freq

radio.rxgain

radio.fem.rxgain

name

lat

lon

prv.key

password

guest.password

owner.info

adc.multiplier

public.key

ver

role

powersaving

repeat

path.hash.mode

loop.detect

txdelay

direct.txdelay

rxdelay

dutycycle

af

int.thresh

cad

agc.reset.interval

multi.acks

flood.advert.interval

advert.interval

flood.max

flood.max.unscoped

flood.max.advert

setperm

acl

allow.read.only

region load

region save

region allowf

region denyf

region get

region home

region default

region put

region def

region remove

region list

region